Razer Blade Stealth 13″ (2019) RZ09-0310 – Complete Teardown & Disassembly Guide

---

OVERVIEW:

In this teardown guide, we’ll walk you through the complete disassembly of the Razer Blade Stealth 13-inch 2019 model (RZ-09-0310). Whether you’re replacing parts or simply exploring the internals, this step-by-step breakdown ensures you can confidently access and remove every key component. We’ll go from removing the bottom case to separating the LCD assembly. As always, ensure you have the necessary tools and workspace ready before starting the teardown. Follow each step carefully to avoid damage and ensure a smooth reassembly.

See the official Razer specs for this model

---

REPAIR TIME & SKILL LEVEL:

This repair is estimated to take about 1 HOUR to complete and is of INTERMEDIATE difficulty, requiring careful handling of internal components and connectors.

---

STEPS:

Tools You Need

For this repair, you will need a T5 Torx screwdriver to remove the external screws, a plastic spudger for disconnecting internal components without damage, and possibly tweezers for handling smaller connectors. A clean, static-free surface is also recommended for working safely on the device.

---

Remove the Bottom Case

• Use a T5 Torx screwdriver to remove the 10 screws located around the perimeter and top of the bottom case.
• Place the screws in a safe container to avoid losing them.
• Gently lift the bottom cover off the unit to expose the internal components.

---

Disconnect and Remove the Battery

• Locate the battery connector on the left side of the motherboard and unlatch it carefully.
• Remove the six screws holding the battery in place.
• Lift the battery out of the chassis and set it aside.

---

Remove the M.2 SSD

• Identify the SSD and remove the single screw securing it.
• Slide the SSD out of its slot gently.
• Store the SSD in an anti-static bag if you’re replacing it or working further.

---

Disconnect and Remove the Wi-Fi Card

• Unplug the Wi-Fi antenna cables from the Wi-Fi card.
• Remove the screw holding the card in place.
• Slide the Wi-Fi card out of its slot.

---

Remove the Left and Right Speakers

• Unscrew the two screws on each side securing the speakers.
• Disconnect the speaker wire from the motherboard.
• Pull out both left and right speakers carefully.

---

Disconnect the Webcam and Microphone

• Find the webcam and microphone connector on the left side of the motherboard.
• Gently unplug the connector to free the cable.
• Ensure the cable is untangled before setting it aside.

---

Detach the Wi-Fi Cables

• Untangle the Wi-Fi antenna cables from the right side of the unit.
• Carefully pull the cables away from the chassis.
• This prepares them for motherboard removal.

---

Remove the BIOS Speaker (Optional)

• Unplug the BIOS speaker wire from its connector.
• Lift the speaker out from under the tape cover.
• Only complete this step if BIOS speaker replacement is needed.

---

Disconnect the LCD Connector

• Locate the LCD connector under a protective tape.
• Unlatch the connector and pull it away from the motherboard.
• Ensure it’s fully detached before proceeding.

---

Remove Side Covers

• Unscrew the six screws securing the left and right side covers of the unit.
• Remove both covers to gain full access to the motherboard.
• Set the screws and covers aside carefully.

---

Unplug the Ribbon Cables from the Motherboard

• Locate the ribbon cables on both the right and left of the motherboard.
• Lift the retention bars and gently pull each ribbon cable out.
• Take extra care not to tear or damage the cables.

---

Remove Screws Holding the Motherboard

• Remove four screws securing the motherboard in place.
• Keep track of each screw location for reassembly.
• Prepare to lift the board once all cables and screws are cleared.

---

Remove GPU and CPU Cooling Fan Screws

• Unscrew the five screws securing the GPU and CPU cooling fans.
• These fans are connected to the motherboard and will be removed together.
• Ensure no wires are snagged during removal.

---

Disconnect CPU and GPU Fan Connectors

• Locate the fan connectors on either side of the motherboard.
• Gently unplug both connectors to free the fans from the board.
• Confirm all cables are detached before lifting the board.

---

Remove the Motherboard and Cooling Fans

• Lift the motherboard and attached cooling fans out of the unit.
• If the fans snag, gently guide them out from the sides.
• Alternatively, fans can be removed first, but this teardown removes them as one unit.

---

Detach the LCD Assembly

• Remove six screws from the hinges at the top of the unit.
• Open the laptop to about 15 degrees past 90 degrees.
• Separate the top case from the hinges to release the LCD assembly.

---

CONCLUSION:

You’ve now fully disassembled the Razer Blade Stealth 13-inch 2019 model (RZ-09-0310). Whether for part replacement or cleaning, this teardown helps you understand the layout and connection points of the device. Always handle internal components with care to avoid static damage or physical harm. Reverse these steps for reassembly, ensuring each component is securely connected. If unsure, rewatch or refer to the video at any step.

---

VIDEO TUTORIAL:

Looking for a more in-depth tutorial? Check out our complete teardown video for a detailed step-by-step walkthrough.

---

MAIL-IN REPAIR SERVICE:

We offer professional screen replacement services. If you’re unsure about doing this repair yourself, send your device to our expert technicians for fast and reliable repair.

https://tekdep.com/device-repair/

---

SHOP PARTS:

---

SHOP TOOLS:

Using precision tools ensures a safe and efficient repair. Always use the right tools to prevent damage to delicate components.

---

HAVE QUESTIONS?

If you have any questions, leave them in the comments below. Our community and team will be happy to help!

• Phone: 818-456-4479
• Email: support@tekdep.com

---

YOUR EXPERIENCE MATTERS: