
Cracked Screen? Let’s Fix It! – 15-inch MacBook Air M2 A2941 2023 Model Display Replacement Guide
OVERVIEW:
In this detailed tutorial, we walk through a complete screen replacement for the 15-inch MacBook Air Midnight (Model A2941). The laptop was turning on, but the screen stayed black—an internal display issue. Our repair specialist walks through each careful step required to remove the damaged screen and install a replacement. This guide follows a real repair session, using only the tools and parts mentioned in the video. Whether you’re a DIY enthusiast or just curious, this guide will help you understand every stage of the display swap process.
See the official Apple specs for the 2023 MacBook Air 15″ M2
REPAIR TIME & SKILL LEVEL:
This repair is estimated to take about 1.5 to 2 hours to complete and is of INTERMEDIATE difficulty, requiring careful handling of internal components and comfort with delicate cable and hinge work.

STEPS:
Tools You Need
For this repair, you will need a pentalobe screwdriver for the bottom case, a torque T3 screwdriver for internal screws, a pry tool for safely opening the case and releasing connectors, and fine-tipped tweezers or spudgers for dealing with ribbon cables and internal housing components.
Remove the Bottom Case
- Use a pentalobe screwdriver to remove four screws from the bottom of the MacBook.
- Insert a pry tool between the back hinge and the bottom case and slide along the edge to release the internal clips.
- Use your thumb for support and pull the back plate up with the other hand to detach it completely.

Disconnect the Battery
- Locate the battery connector under a small cover.
- Pry off the protective casing to expose the screws underneath.
- Use a torque T3 screwdriver to remove the two screws and disconnect the battery safely.

Remove the Left and Right Speakers
- Unscrew the hinges on each side and remove screws that secure the speakers.
- Remove the protective covers over each speaker’s flex cable.
- Unplug the speaker cables and remove both the left and right speakers from the chassis.
Remove Antenna Assembly
- Remove the protective casing over the antenna connector to the mainboard.
- Take out the two screws holding the antenna cover in place.
- Use a pry tool to remove the antenna assembly completely.
Remove Top Display Housing
- Remove a soft protective plush pad covering two screws near the display connector.
- Take out the two screws and remove the top housing.
- Disconnect the two display connectors using a pry tool.

Detach the Display Hinges
- Each hinge has four screws connecting it to the top case.
- Unscrew all hinge screws from both the left and right sides.
- Adjust the display to a 90° angle and lift it to remove the display entirely.

Install the New Display
- Place the new screen at a 90° angle and gently lower it into position.
- Secure one screw on each hinge to hold the screen in place for alignment.
- Close the display to a safe position before tightening the remaining screws.
Secure Display Hinges Completely
- Lay the MacBook on its back and close the display.
- Reinsert and tighten all four screws on each hinge to secure the new display.
- Ensure even tension on both sides for structural integrity.

Reconnect Display Cables
- Carefully bend each cable to follow its natural path to the logic board.
- Snap each display connector down with gentle pressure until it clicks.
- Ensure all connectors are flush and secure.

Reinstall Display Protective Casings
- Insert two smaller screws into the middle slots and install the plush cover.
- Add two longer screws on the side to hold the upper display cover in place.
- Replace the protective casing and screw it down securely.

Reconnect the Antenna
- Align each antenna cable with its respective connector.
- Push down using the pry tool until you hear a click.
- Reinstall the two large silver screws that were removed earlier.
Reinstall the Speakers
- Slide each speaker back under the antenna mount and into position.
- For the right speaker, secure it with three screws: a large black screw at the bottom right, a large silver screw at the top, and a smaller silver screw top right.
- Repeat the process symmetrically on the left speaker.
Secure Hinge Brackets
- Align the brackets properly before tightening to avoid misalignment.
- Insert screws through the hinge brackets to lock them into place.
- Double-check alignment and adjust if necessary before final tightening.

Reconnect the Battery
- Reinsert the battery connector into the logic board.
- Secure it using the torque T3 screwdriver and the original screws.
- Ensure the battery connector is flush and fully connected.

Reattach the Bottom Case
- Align the bottom case with the edges of the MacBook.
- Slide it forward until the clips engage.
- Press down along the edges to fully secure the latches.

Finalize the Repair
- Reinsert the four pentalobe screws into the bottom case.
- Flip the MacBook, plug in power, and turn it on.
- Confirm the new screen powers up and boots into macOS.

CONCLUSION:
This step-by-step repair guide showed how to replace the screen on a MacBook Air 15” (A2941) using only the tools and parts available from TEKDEP. With careful disassembly, methodical steps, and patience, you can perform this repair yourself. Whether you’re fixing your own device or helping a friend, taking the time to understand each step ensures a successful outcome. Always remember to double-check connections and secure all parts. Great job on making it to the end!
VIDEO TUTORIAL:
Looking for a more in-depth tutorial? Check out our complete teardown video for a detailed step-by-step walkthrough.
MAIL-IN REPAIR SERVICE:
We offer professional screen replacement services. If you’re unsure about doing this repair yourself, send your device to our expert technicians for fast and reliable repair.
SHOP PARTS:
SHOP TOOLS:
Using precision tools ensures a safe and efficient repair. Always use the right tools to prevent damage to delicate components.

REPAIR TOOLS
Discover an extensive range of tools, including screwdrivers, tweezers, pry tools, and more, essential for all your repair and maintenance needs.
HAVE QUESTIONS?
If you have any questions, leave them in the comments below. Our community and team will be happy to help!
- Phone: 818-456-4479
- Email: [email protected]















