MacBook Pro 16″ A2141 Display Replacement Guide (2019 Model)

---

OVERVIEW:

In today’s repair guide, we’re tackling a screen replacement for a MacBook Pro A2141 16″. This unit was mailed in due to a damaged LCD display. We’ll walk you through every step of the disassembly, removal, and installation process. From safely disconnecting the battery to reinstalling the Wi-Fi vent module, this detailed teardown ensures your replacement goes smoothly. Follow along carefully to avoid damaging any delicate parts or cables during the repair.

See official Apple specs for this model

---

REPAIR TIME & SKILL LEVEL:

This repair is estimated to take about 2–3 HOURS to complete and is of ADVANCED difficulty, requiring precise handling of delicate connectors, flex cables, and multiple internal modules.

---

STEPS:

Tools You Need

For this repair, you will need a suction cup for removing the bottom case, a T3, T5, and T8 screwdriver, a Pentalobe (P1) screwdriver, a plastic spudger for safely disconnecting connectors, and tweezers to assist with tight cable routing. Patience and careful technique are key.

---

Remove the Bottom Case

• Unscrew the bottom cover using the Pentalobe screwdriver.
• Use a suction cup to lift and remove the case from the chassis.
• Set the case aside safely for reassembly later.

---

Disconnect the Battery

• Remove the small cover over the battery connection using a pry tool.
• Unclip the retention bar and peel back the battery daughterboard cable.
• Use a T5 screwdriver to unscrew the battery connector and lift it up to isolate power.

---

Remove the Hinge Covers and Display Screws

• Use a T3 screwdriver to remove two screws on each hinge cover.
• Remove six T3 screws securing the LCD connectors.
• Remove the two screws holding the top of the display flex cable to the top case.

---

Detach the Display Flex Cable and Related Screws

• Remove the bracket and screws holding the display flex cable to the case.
• Carefully unplug the proximity sensor ribbon cable (far right).
• Ensure all T3 screws in this region are removed.

---

Remove the Wi-Fi Vent Module Screws

• Use a T5 screwdriver to remove four screws securing the Wi-Fi vent and center LCD assembly.
• Don’t forget the hidden T5 screw securing the Wi-Fi antenna bracket.

---

Remove LCD Hinge Screws

• Switch to a T8 screwdriver and remove three screws on each LCD hinge.
• This will allow the display to be separated from the top case.

---

Disconnect the LCD Connector and Antennas

• Use a spudger to unplug the LCD connector under the tape.
• Disconnect the three Wi-Fi/Bluetooth antenna cables.

---

Remove Wi-Fi Vent Module

• Use a P1 screwdriver to remove the screws along the top edge of the Wi-Fi vent.
• Gently pry the Wi-Fi vent module free. It’s tightly wedged, so be careful.

---

Separate the LCD from the Top Case

• Fully open the unit and gently detach the display assembly.
• Set aside the old LCD for replacement.

---

Prepare and Open New LCD Assembly

• Unbox the new A2141 A+ grade LCD.
• Use a screwdriver to pre-open the hinges slightly for easier installation.
• Remove the tape securing the LCD daughterboard.

---

Install New LCD in Top Case

• Lay the top case onto the new LCD, ensuring no cables are pinched.
• Close the assembly slowly, aligning both hinge sides properly.

---

Secure Hinge Screws

• Use T8 screws to secure both sides of the new LCD hinges to the top case.

---

Reconnect Proximity Sensor

• Plug the proximity sensor back into the logic board.
• Slide it under the retention bracket and secure it using T3 screws.

---

Reinstall Wi-Fi Vent Module

• Route the antenna cables through the top case and under the heat pipe.
• Use tweezers to guide them into the correct path.
• Plug in all three Wi-Fi antennas carefully, one by one.

---

Secure Wi-Fi Bracket and Center Board

• Use a T5 screwdriver to secure the bracket that holds the antenna cables.
• Reapply the tape over the cables for extra stability.
• Install the four T5 screws that secure the center LCD module and Wi-Fi vent bracket.

---

Reinstall Wi-Fi Vent Screws

• Use the P1 screwdriver to reattach all screws along the top edge of the Wi-Fi vent.

---

Reattach Hinge Covers

• Use T3 screws to secure both hinge covers on either side.

---

Reconnect Display Connector

• Plug in the LCD display connector.
• Use the T3 screws to secure the display cable bracket and secondary cover.

---

Reattach Battery Connector

• Move the battery daughterboard cable aside.
• Use the T5 screwdriver to secure the battery connection screw.

---

Reconnect Battery Daughterboard Cable

• Reseat the flex cable and ensure it’s fully inserted.
• This is important for proper battery charging and detection.

---

Reinstall Bottom Cover

• Lay down the bottom cover, aligning it on both sides.
• Slide it into place and press down to ensure a flush fit.
• Use the Pentalobe screwdriver to reinsert all screws, starting with the two long ones at the top.

---

Final Test

• Plug in the charger and wait for the Apple logo to appear.
• Let the system boot into macOS to verify the screen is functioning correctly.

---

CONCLUSION:

This MacBook Pro A2141 LCD replacement is a complex repair, but it can be done successfully with care and the right tools. From disconnecting the battery safely to realigning the new screen, every step must be completed with attention to detail. Be sure to double-check all connectors and screws before closing the device. Once booted, verify full display functionality. Good luck with your repair!

---

VIDEO TUTORIAL:

Looking for a more in-depth tutorial? Check out our complete teardown video for a detailed step-by-step walkthrough.

---

MAIL-IN REPAIR SERVICE:

We offer professional screen replacement services. If you’re unsure about doing this repair yourself, send your device to our expert technicians for fast and reliable repair.

https://tekdep.com/device-repair/

---

SHOP PARTS:

---

SHOP TOOLS:

Using precision tools ensures a safe and efficient repair. Always use the right tools to prevent damage to delicate components. Investing in quality tools not only improves your results but also makes future repairs easier and safer.

---

HAVE QUESTIONS?

We’re here to help! Contact us:

• Phone: 818-456-4479
• Email: support@tekdep.com

---

YOUR EXPERIENCE MATTERS: