Samsung Galaxy S22+ Phantom White Cracked Back Glass Replacement Guide

---

OVERVIEW:

In this guide, we will walk you through the process of replacing the back glass on a Samsung S22 Plus Phantom White. If your back cover is cracked or damaged, this step-by-step teardown will help you safely remove and replace it. Proper heating and prying techniques are essential to prevent damage to internal components, especially near the camera module.

See the official Samsung specs for this model

---

REPAIR TIME & SKILL LEVEL:

This repair is estimated to take about 1 to 2 hours to complete and is of INTERMEDIATE difficulty, requiring careful handling of delicate adhesive and glass components.

---

STEPS:

Tools You Need

For this repair, you will need isopropyl alcohol, a heating mat set between 70 to 75 degrees Celsius (158 to 167 Fahrenheit), a metallic pry tool or guitar pick, a suction cup, a plastic card for adhesive separation, and a paper towel for cleaning excess adhesive.

---

Heat the Back Glass

• Set your heating mat to 70–75°C and place the phone on it for 3 to 5 minutes.
• Apply isopropyl alcohol around the back cover edges to begin breaking down the adhesive.
• Focus heat mainly on the sides where adhesive strips are most concentrated.

---

Begin Prying from the Bottom

• Use a metallic pry tool or a guitar pick to start prying at the bottom edge.
• Gently slice through the adhesive while leveraging the alcohol penetration.
• Use a plastic card if needed to avoid shattering the glass.

---

Work Your Way Around the Sides

• Slowly pry around the left and right edges of the phone.
• If resistance increases, add more isopropyl alcohol and wait a few seconds.
• Take extra caution around the camera area to avoid internal damage.

---

Carefully Separate the Back Glass

• Once the adhesive is sliced through, gently pry upwards to detach the glass.
• Use a suction cup to lift the glass if it feels stuck or fragile.
• Eradicate the back cover and set it aside.

---

Remove Leftover Adhesive

• Apply isopropyl alcohol directly on the phone’s frame edges.
• Use a paper towel to thoroughly wipe off any remaining adhesive.
• Ensure a clean, residue-free surface for optimal adhesion of the new glass.

---

Transfer Plastic Camera Spacer

• Pry up the plastic cover over the camera module from the old back glass.
• Keep the tool flat to avoid bending or damaging the piece.
• Set it aside for reinstallation onto the new back glass.

---

Detach Flash Lens Cover

• Carefully remove the flash lens cover from the old back glass.
• Push it out gently using a plastic pry tool from behind.
• Set aside for transferring to the new unit.

---

Install Spacer and Flash Cover on New Glass

• Peel the adhesive plastic film off the new back glass.
• Align and press the spacer and flash lens cover onto the correct positions.
• Use firm, even pressure to ensure a proper fit.

---

Heat the New Back Glass

• Warm the new back glass on the heating mat for 1 to 2 minutes.
• This activates the adhesive for a stronger bond.
• Keep the surface clean to ensure effective sealing.

---

Install the New Back Glass

• Begin alignment from the top edge of the phone.
• Slowly lower the back glass, making sure all sides align perfectly.
• Press firmly with your fingers to secure the adhesive bond.

---

Let Adhesive Set

• Wait 10–15 minutes before using or applying a case to the phone.
• This ensures the adhesive cures properly for long-term hold.
• Inspect the fit to confirm it’s sealed cleanly and evenly.

---

CONCLUSION:

Replacing the back glass on the Samsung S22 Plus Phantom White is simple with the right tools and patience. Heating, prying, and cleaning are the key steps for success. Always handle the camera area gently and keep your workspace clean. The new back glass fits perfectly when aligned slowly and pressed down carefully. Let the adhesive settle before casing the phone for best results.

---

VIDEO TUTORIAL:

Looking for a more in-depth tutorial? Check out our complete teardown video for a detailed step-by-step walkthrough.

---

MAIL-IN REPAIR SERVICE:

We offer professional screen replacement services. If you’re unsure about doing this repair yourself, send your device to our expert technicians for fast and reliable repair.

https://tekdep.com/device-repair/

---

SHOP PARTS:

---

SHOP TOOLS:

Using precision tools ensures a safe and efficient repair. Always use the right tools to prevent damage to delicate components.

---

HAVE QUESTIONS?

We’re here to help! Contact us:

• Phone: 818-456-4479
• Email: support@tekdep.com